Request a quote

BALANS modules

Every BALANS switch consists of three boards: a FACE front panel, the CORE controller board and a POWER module. Pick the panel by how you want to control and the module by what is to be switched. The controller board is always the same.

In development

We are testing the rev B prototype boards right now. Sales start once the safety, EMC and radio tests are finished. Until then we are looking for pilot installations.

  • Prototype boards are built and being tested
  • In development board design and firmware driver are done, not yet verified on hardware
  • Coming up design is done, production is being finished
  • None of this is on sale yet.

FACE front panels

All fit behind the same 84 × 84 mm glass and have LED backlighting. The Bosch BME688 sensor (temperature, humidity, pressure, air quality) is optional: panels will also come without the sensor and then take the temperature from another BALANS switch or from Home Assistant.

BALANS FACE Classic (vizualizace)
Prototype

FACEClassic

The classic behind glass

Five touch pads behind glass: a large one in the middle, four in the corners.

  • Light in the middle, scenes and blinds in the corners
  • 5 RGB LEDs, proximity detection, haptic feedback (optional)
  • Fits a hallway, room or kitchen
Manual and wiring
BALANS FACE Chevron (vizualizace)
Prototype

FACEChevron

Brightness with one swipe

Five pads and a touch slider of eight chevrons for smooth dimming.

  • Slider of 8 chevrons + 5 pads
  • 13 RGB LEDs, proximity detection, haptic feedback (optional)
  • Fits a living room, bedroom or dining room
Manual and wiring
BALANS FACE Sense (vizualizace)
In development

FACESense

Knows you are in the room

Two touch pads, a presence radar and a light sensor.

  • 24 GHz radar detects motion and still presence
  • Sends presence, distance and light level to Home Assistant and the PLC. The radar switches nothing itself; automations decide.
  • Fits a hallway, toilet, study or a bathroom outside zones 0–2
Manual and wiring
BALANS FACE Display (vizualizace)
Coming up

FACEDisplay

Display and voice

A round touch display, microphone and speaker for voice control.

  • Round 1.43″ 466 × 466 AMOLED with touch, brightness arc
  • MEMS microphone and speaker amplifier, ring of 12 RGB LEDs
  • Home Assistant Assist voice satellite (coming up)
Manual and wiring

CORE controller board

The same in every set: ESP32-S3, 2.4 GHz Wi-Fi, Ethernet with the Base and PoE IO modules, web interface, MQTT and Modbus TCP. RS485 for Modbus RTU comes with revision C and is in development.

BALANS CORE (vizualizace)
Prototype

CORE

The same brain in every set

The controller board with ESP32-S3, Wi-Fi, Ethernet and RS485, the same in every set.

  • ESP32-S3, 8 MB flash, 2 MB PSRAM, USB-C for service
  • 2.4 GHz Wi-Fi, Ethernet with the POWER Base and PoE IO modules
  • Web interface, MQTT, Modbus TCP; RS485 for Modbus RTU in rev C (in development)
Manual and wiring

POWER modules

For the bottom of the box. 230 V modules are connected by an electrician only. Load ratings are preliminary until the temperature-rise tests are finished.

BALANS POWER Relay (vizualizace)
Prototype

POWERRelay

Two lights, zero-cross switching

Two 230 V relays with zero-cross switching.

  • 230 V luminaires and LED drivers, resistive loads
  • Up to 5 A per output and 5 A in total (preliminary)
  • Revision C is coming up: standard relays and reinforced insulation between mains and the low-voltage part; terminals and wiring stay the same. The renders show rev C
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
230 V luminaires and LED drivers, resistive loads up to 5 A
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring
BALANS POWER Triac (vizualizace)
Prototype

POWERTriac

Two 230 V dimmers

Two leading-edge 230 V dimmers.

  • Incandescent, halogen and dimmable LED lamps
  • About 230 W per channel (preliminary)
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
230 V incandescent and halogen lamps, dimmable LED lamps (leading edge)
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring
BALANS POWER Dimmer LED (vizualizace)
Coming up

POWERDimmer LED

A dimmer for LED lamps

A dimmer with MOSFET transistors: one channel up to 250 W and two inputs for 230 V push-buttons.

  • Dimmable 230 V LED lamps and luminaires, incandescent and halogen lamps up to 250 W (from calculation)
  • Trailing edge, gentle on LEDs, or leading edge; electronic short-circuit protection
  • The board is designed and not measured yet; the firmware recognises the module, control is in development
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
dimmable 230 V LED lamps and luminaires, incandescent and halogen lamps up to 250 W; two existing 230 V push-buttons
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring
BALANS POWER RGBW (vizualizace)
Prototype

POWERRGBW

RGBW, CCT and white LED strips

Four PWM channels for 12 / 24 V LED strips.

  • RGBW, CCT or 4× single-colour strips, common anode
  • Up to 2 A per channel, 8 A in total (preliminary)
  • 12–24 V DC (SELV) · Wi-Fi
You connect:
12/24 V common-anode LED strips: RGBW, CCT or 4× single colour
Supply:
12–24 V DC (SELV)
Network:
Wi-Fi
Manual and wiring
BALANS POWER Base (vizualizace)
Prototype

POWERBase

One cable: data and power

PoE or 12–24 V power and Ethernet for a switch without outputs.

  • Sends touches and sensors to Home Assistant or a PLC, controls other switches, works as a thermostat
  • Box at least 60 mm deep because of the RJ45
  • PoE or 12–24 V DC · Ethernet or Wi-Fi
You connect:
nothing: the switch sends events to HA or a PLC, controls other BALANS switches or acts as a thermostat
Supply:
PoE 802.3af or 12–24 V DC
Network:
Ethernet (PoE) or Wi-Fi
Manual and wiring
BALANS POWER PoE IO (vizualizace)
Coming up

POWERPoE IO

Building services in a switch

PoE, Ethernet and inputs and outputs for building services.

  • 4× DI (contact, S0, 24 V), 2× DO 24 V 0.5 A
  • 2× AO 0–10 V / 4–20 mA, 2× AI including PT1000 and NTC
  • PoE or 24 V DC · Ethernet
You connect:
4× DI (contact, S0, 24 V), 2× DO 24 V 0.5 A, 2× AO 0–10 V / 4–20 mA, 2× AI incl. PT1000 and NTC
Supply:
PoE or 24 V DC
Network:
Ethernet (PoE)
Manual and wiring
BALANS POWER DALI (vizualizace)
In development

POWERDALI

DALI for up to 64 drivers

A DALI master for dimming up to 64 drivers over two wires.

  • Up to 64 addresses and 16 groups; brightness (DT6), tunable white and RGBW (DT8)
  • The bus is powered by a separate DALI supply
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
DALI drivers and ballasts (DT6 brightness, DT8 tunable white and RGBW), 16 groups
Supply:
230 V AC and neutral; the bus is fed by an external DALI supply
Network:
Wi-Fi
Manual and wiring
BALANS POWER Blinds (vizualizace)
In development

POWERBlinds

A shutter or a blind

Control of one 230 V shutter or blind including slat tilt.

  • 1 shutter, blind or awning motor up to 3 A (preliminary)
  • Position in percent, slats following the sun, wind and rain lock
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
1 shutter, blind or awning motor, 230 V up to 3 A
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring
BALANS POWER 0–10 V (vizualizace)
In development

POWER0–10 V

1–10 V LED drivers

Switching of the LED driver and two 1–10 V control lines.

  • Relay for the driver supply, zero-cross switching
  • 2× passive 1–10 V line, galvanically isolated
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
LED driver supply (zero-cross relay) and 2× 1–10 V control line
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring
BALANS POWER Heat Triac (vizualizace)
In development

POWERHeat Triac

Underfloor heating

Two 230 V thermal actuators and two temperature sensors for underfloor heating.

  • 2× 230 V triac up to 0.5 A, zero-cross switching
  • 2× NTC 10k or PT1000 sensor; watches the floor temperature limit, does not replace a safety limiter
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
2× 230 V thermal actuator (up to 0.5 A), 2× NTC 10k or PT1000 sensor
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring
BALANS POWER Heat Relay (vizualizace)
In development

POWERHeat Relay

Electric heating with metering

A 16 A relay with energy metering and temperature inputs for electric heating.

  • Heating cables, mats, panel heaters; the rated load follows after testing
  • Measures V, A, W and kWh; calibration will be verified on the first unit
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

You connect:
heating cables, mats and direct heaters (16 A relay, rating after testing), V, A, W and kWh metering, 2× NTC or PT1000 sensor
Supply:
230 V AC and neutral
Network:
Wi-Fi
Manual and wiring

How to choose

  1. What do you want to control?

    230 V light: POWER Relay. Dimming LED lamps: POWER Dimmer LED (coming up). Two dimmed circuits or a fan: POWER Triac. LED strip: POWER RGBW. DALI: POWER DALI. 1–10 V drivers: POWER 0–10 V. Shutter: POWER Blinds. Underfloor heating: POWER Heat Triac. Electric heating: POWER Heat Relay. Buttons only for HA or a PLC: POWER Base. 24 V inputs and outputs: POWER PoE IO.

  2. How do you want to control it?

    The classic way: FACE Classic or Quad. Dimming with a swipe: FACE Chevron. Light by presence: FACE Sense. Display and voice: FACE Display.

  3. Is there a neutral wire in the box?

    The 230 V modules need it. Without it choose PoE or 12–24 V supply with the POWER Base or POWER PoE IO module.

Not sure? Tell us what you need in the room and we will propose the set.

Write to us Join the pilot What BALANS controls Sets by room

Be there when BALANS launches

We will e-mail you when the modules go on sale and, once in a while, a short note on how development is going. No spam.

I want a pilot installation Write to us

Privacy policy