Request a quote

What BALANS can do

Everything on this page runs right in the switch. You need no cloud, no account and no vendor app.

In development

The features are programmed and we are verifying them on prototypes step by step. Features marked “coming up” belong to modules in development.

An AI-assisted visualisation (44 s, no sound). The display screens follow the firmware; the interiors and hands are illustrative. The POWER Blinds and Heat modules are in preparation.

Feature overview

Setup without an app

  • Setup wizard walks you through the name and room, the panel and module selection, touch calibration, Wi-Fi and the Home Assistant connection. Nothing is saved until you finish the wizard.
  • Three web modes: Standard for everyday use, Advanced and Expert for installation and tuning. Warning cards are always visible.
  • The switch recognises its module. Before enabling the outputs it checks which power module is attached. If it does not match the settings, the outputs stay off. A new switch selects a common module by itself.
  • Touch calibration through glass from the web or right on the switch: the pad backlight shows when to touch and when to release.
  • Web interface in five languages: Czech, Slovak, English, Polish and German, light and dark theme, comfortable on a phone too.
  • If Wi-Fi does not connect, the switch says why: the network was not found, the password does not match, or the security does not fit. It shows the signal strength in bars.
  • Settings change history: you see the last eight changes and undo the latest one with a single button.

Lights and outputs

  • Dimming by holding a pad or swiping the slider, with an adjustable curve and maximum brightness.
  • Lowest-brightness wizard: dims the light step by step and finds the level below which an LED lamp starts to flicker.
  • Auto-off and staircase timer: the light warns you before it goes out and another press extends the time.
  • State after power-up for each output separately: restore the last state, always off, or always on.
  • Scenes: eight stored combinations of outputs and brightness at one touch.
  • Brightness by time of day: a dimmed light turns on fully during the day and softly at night.
  • Night path: at night only a gentle light to find your way.

Touch and backlight

  • Gestures: short and long touch, hold, slider swipe and a palm tap for one main action. You switch on double and triple touch for the buttons where you want them.
  • Slider: you set the brightness by sliding a finger, the LED bar shows the set level.
  • Wet glass is no problem: an area that would switch by itself turns off and flashes red. The others keep working.
  • Cleaning lock and child lock. Wipe the glass without switching anything.
  • Backlight with separate brightness for on, off and idle. Night brightness by the clock or by sunset and sunrise.
  • LED notifications from Home Assistant: doorbell, washing machine, open window.
  • Air quality by colour: the idle backlight shows green to red depending on the air in the room. It can be set to show up only when the air gets worse.

Display Coming up

The FACE Display panel.

  • Widgets: clock, thermostat, climate, air quality, lights, scenes, timers, blinds and data from Home Assistant.
  • Settings right on the display: brightness, volume, night quiet, holiday mode, heating programme.
  • Countdown up to three hours with a beep at the end.
  • Display child lock: holding for three seconds unlocks it for a minute.

Time and automation

  • Scheduler: twelve entries, by time or by sunrise and sunset. Optional condition: only in the dark, only in daylight, below or above a set temperature.
  • Holiday mode turns selected lights on at random.
  • Time even without internet: in a network without internet the switch takes the time from the browser.

Temperature and heating

  • Room thermostat with a weekly programme, early start, an open-window pause and frost protection. If the temperature reading is lost, the output turns off.
  • The air sensor is optional. One switch with a sensor per room is enough; the others take the temperature from it. Home Assistant can be the source too.
  • Underfloor and electric heating with the POWER Heat modules: floor temperature limit, overheating protection and energy metering (coming up).

Shutters and blinds Coming up

The POWER Blinds module.

  • Position in per cent and slat tilt.
  • Slats follow the sun: based on the location of the house and the orientation of the window.
  • Wind and rain lock: the blind goes up and cannot be lowered while the lock lasts.

Presence Coming up

The FACE Sense panel.

  • Presence-based light even without Home Assistant: it switches on when you enter and it is dark, and off when the room is empty.
  • Switching off by hand has priority: what you switch off by hand does not come on again by itself until you leave.

Switch to switch

  • Linking without a server: a staircase, a long hallway or “all off” at the door. Messages are signed.
  • Shared temperature between switches in the same room.

For installers

  • Handover to the customer: one action at the end of the installation deletes the traces of testing (log, charts, tokens, sessions) and offers to set passwords that only the customer will know.
  • Setting up a new switch over USB and bulk rollout with the PC tool for managing several switches.
  • A link to the manual for the panel and the module right in the switch's web interface.

When something does not work

  • Device health in one word: OK, warning or error, with the reason right below.
  • Error codes E01 to E26 with a description of what they mean and what to do. In the web interface, in Home Assistant, over MQTT and in a PLC over Modbus.
  • On a serious error the backlight flashes red three times.
  • Event log and charts of temperature, humidity and air quality for seven days.
  • Service bundle: one file for support, without passwords or keys.
  • Safe mode: if the firmware fails, the web interface and updates stay available.

Security and updates

  • Login without sending the password over the network, administrator and control-only roles, optional HTTPS.
  • Signed updates: if the network and web interface do not come up after an update, the switch rolls back to the previous version by itself.
  • Nightly automatic update from your own server is optional. It only runs when nothing is lit and nobody is touching the switch.
  • No data to the vendor. The switch sends us nothing.

Integrations

Home Assistant, MQTT, REST API, webhooks and Modbus TCP for PLCs.

All about integrations All modules

Be there when BALANS launches

We will e-mail you when the modules go on sale and, once in a while, a short note on how development is going. No spam.

I want a pilot installation Write to us

Privacy policy