Request a quote
BALANSby Benešl Automation
In development · rev B prototypes

A smart switch behind glass. No cloud.

A modular switch for a standard 68 mm wall box. Touch through glass, air sensors, Wi-Fi or PoE. It talks to Home Assistant and to PLCs.

  • Fits a 68 mm wall box
  • Local, no cloud
  • Home Assistant · MQTT · Modbus TCP
FACE front panels behind 84 × 84 mm glass
5
CORE controller board for every set
1
POWER modules for the bottom of the box
11
clouds, accounts or vendor apps
0

BALANS is the new name of the system we previously presented as Smart Button.

An AI-assisted visualisation made from 3D models of the panels, not footage of a real device. The interiors and hands are illustrative; the display panel is a design proposal.
In development

We are testing the rev B prototype boards right now. Sales start once the safety, EMC and radio tests are finished. Until then we are looking for pilot installations.

Three layers, one switch

The name BALANS means balance: between design and engineering, between comfort and control over your own data. Every switch is three layers stacked in one box, just like the three ovals in the logo.

Exploded BALANS FACE Classic + CORE + POWER set: box, power module, carrier, controller board, frame, front panel and glass (visualisation)
  1. FACE – what you see

    The front panel behind 84 × 84 mm glass. Touch pads, a slider, a presence radar or a round display. LED backlight in every panel, an air sensor as an option.

  2. CORE – what thinks

    The controller board with ESP32-S3, Wi-Fi, Ethernet and now RS485 as well. The same in every set. It runs the BALANS firmware, the web interface and all integrations.

  3. POWER – what switches

    The power module at the bottom of the box. It decides what the switch controls and how it is powered: relay, dimmer, LED strip, DALI, blinds, heating or PoE with inputs and outputs. An electrician can swap it for another one later.

What BALANS controls

One switch, eleven power modules. Behind BALANS you connect 230 V luminaires, dimmable LEDs, LED strips, a DALI bus, 0–10 V drivers, shutters and blinds, underfloor heating actuators and heating cables. And over the network anything that Home Assistant, MQTT, a REST API or your PLC can handle.

Diagram: the BALANS switch, its FACE, CORE and POWER layers, networks and integrations and ten power modules with their loads
The DALI, Blinds, 0–10 V and Heat modules are in development.

Detailed overview of what connects where

Why BALANS

A smart switch that fits a regular electrical installation and needs neither a cloud nor a vendor app.

Beautiful and quiet

Glass with no buttons or gaps. The panel lights up as your hand approaches and confirms the touch with a short vibration. At night it glows only gently.

Smart even without a server

Scenes, a scheduler with sunrise and sunset, a thermostat with a weekly programme, a staircase timer and a night mode run right in the switch. Switches can link to each other, for a staircase or “all off” at the door. If the Wi-Fi or the router goes down, the light still turns on and off.

Yours, not ours

No cloud, no account, no vendor app. The switch communicates only within your network and sends no data to the manufacturer.

Open for integrations

Home Assistant (MQTT discovery, LED notifications, energy, Assist voice), MQTT for Node-RED and other systems, a REST API and webhooks, Modbus TCP for PLCs with a ready-made block for S7-1500. And a web interface in five languages that works without the internet and guides you through setup step by step.

Wi-Fi, Ethernet and PoE

Most modules run over Wi-Fi. With the POWER Base and POWER PoE IO modules a single cable carries data and power.

Built to last

Needs change? Only the panel or the power module is replaced, not the whole switch. Firmware updates over the web and rolls back by itself after a failed update. When something is wrong, the switch says so with a clear error code in the web interface, in Home Assistant and in the PLC.

FACE front panels

Five ways to control behind the same 84 × 84 mm glass. All have LED backlight. The Bosch BME688 sensor for temperature, humidity, pressure and air quality is optional: one per room is enough, the other switches take the temperature from it.

BALANS FACE Classic (vizualizace)
Prototype

FACEClassic

The classic behind glass

Five touch pads behind glass: a large one in the middle, four in the corners.

  • Light in the middle, scenes and blinds in the corners
  • 5 RGB LEDs, proximity detection, haptic feedback (optional)
  • Fits a hallway, room or kitchen
Manual and wiring
BALANS FACE Chevron (vizualizace)
Prototype

FACEChevron

Brightness with one swipe

Five pads and a touch slider of eight chevrons for smooth dimming.

  • Slider of 8 chevrons + 5 pads
  • 13 RGB LEDs, proximity detection, haptic feedback (optional)
  • Fits a living room, bedroom or dining room
Manual and wiring
BALANS FACE Quad (vizualizace)
Prototype

FACEQuad

Four circuits, four pads

Four equal pads for four lights, blinds or scenes.

  • 4 touch pads, 4 RGB LEDs
  • Proximity detection, haptic feedback (optional)
  • Fits rooms with several circuits and offices
Manual and wiring
BALANS FACE Sense (vizualizace)
In development

FACESense

Knows you are in the room

Two touch pads, a presence radar and a light sensor.

  • 24 GHz radar detects motion and still presence
  • Sends presence, distance and light level to Home Assistant and the PLC. The radar switches nothing itself; automations decide.
  • Fits a hallway, toilet, study or a bathroom outside zones 0–2
Manual and wiring
BALANS FACE Display (vizualizace)
Coming up

FACEDisplay

Display and voice

A round touch display, microphone and speaker for voice control.

  • Round 1.43″ 466 × 466 AMOLED with touch, brightness arc
  • MEMS microphone and speaker amplifier, ring of 12 RGB LEDs
  • Home Assistant Assist voice satellite (coming up)
Manual and wiring

Glass and frame colours

Black glass, white frame
Black glass, white frame
White glass, white frame
White glass, white frame
Black glass, anthracite frame
Black glass, anthracite frame

The CORE board and POWER modules

CORE is the same in every set. The POWER module at the bottom of the box decides what the switch controls and how it is powered.

BALANS CORE (vizualizace)
Prototype

CORE

The same brain in every set

The controller board with ESP32-S3, Wi-Fi, Ethernet and RS485, the same in every set.

  • ESP32-S3, 8 MB flash, 2 MB PSRAM, USB-C for service
  • 2.4 GHz Wi-Fi, Ethernet with the POWER Base and PoE IO modules
  • Web interface, MQTT, Modbus TCP; RS485 for Modbus RTU in rev C (in development)
Manual and wiring
BALANS POWER Relay (vizualizace)
Prototype

POWERRelay

Two lights, zero-cross switching

Two 230 V relays with zero-cross switching.

  • 230 V luminaires and LED drivers, resistive loads
  • Up to 5 A per output and 5 A in total (preliminary)
  • Revision C is coming up: standard relays and reinforced insulation between mains and the low-voltage part; terminals and wiring stay the same. The renders show rev C
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER Triac (vizualizace)
Prototype

POWERTriac

Two 230 V dimmers

Two leading-edge 230 V dimmers.

  • Incandescent, halogen and dimmable LED lamps
  • About 230 W per channel (preliminary)
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER Dimmer LED (vizualizace)
Coming up

POWERDimmer LED

A dimmer for LED lamps

A dimmer with MOSFET transistors: one channel up to 250 W and two inputs for 230 V push-buttons.

  • Dimmable 230 V LED lamps and luminaires, incandescent and halogen lamps up to 250 W (from calculation)
  • Trailing edge, gentle on LEDs, or leading edge; electronic short-circuit protection
  • The board is designed and not measured yet; the firmware recognises the module, control is in development
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER RGBW (vizualizace)
Prototype

POWERRGBW

RGBW, CCT and white LED strips

Four PWM channels for 12 / 24 V LED strips.

  • RGBW, CCT or 4× single-colour strips, common anode
  • Up to 2 A per channel, 8 A in total (preliminary)
  • 12–24 V DC (SELV) · Wi-Fi
Manual and wiring
BALANS POWER Base (vizualizace)
Prototype

POWERBase

One cable: data and power

PoE or 12–24 V power and Ethernet for a switch without outputs.

  • Sends touches and sensors to Home Assistant or a PLC, controls other switches, works as a thermostat
  • Box at least 60 mm deep because of the RJ45
  • PoE or 12–24 V DC · Ethernet or Wi-Fi
Manual and wiring
BALANS POWER PoE IO (vizualizace)
Coming up

POWERPoE IO

Building services in a switch

PoE, Ethernet and inputs and outputs for building services.

  • 4× DI (contact, S0, 24 V), 2× DO 24 V 0.5 A
  • 2× AO 0–10 V / 4–20 mA, 2× AI including PT1000 and NTC
  • PoE or 24 V DC · Ethernet
Manual and wiring
BALANS POWER DALI (vizualizace)
In development

POWERDALI

DALI for up to 64 drivers

A DALI master for dimming up to 64 drivers over two wires.

  • Up to 64 addresses and 16 groups; brightness (DT6), tunable white and RGBW (DT8)
  • The bus is powered by a separate DALI supply
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER Blinds (vizualizace)
In development

POWERBlinds

A shutter or a blind

Control of one 230 V shutter or blind including slat tilt.

  • 1 shutter, blind or awning motor up to 3 A (preliminary)
  • Position in percent, slats following the sun, wind and rain lock
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER 0–10 V (vizualizace)
In development

POWER0–10 V

1–10 V LED drivers

Switching of the LED driver and two 1–10 V control lines.

  • Relay for the driver supply, zero-cross switching
  • 2× passive 1–10 V line, galvanically isolated
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER Heat Triac (vizualizace)
In development

POWERHeat Triac

Underfloor heating

Two 230 V thermal actuators and two temperature sensors for underfloor heating.

  • 2× 230 V triac up to 0.5 A, zero-cross switching
  • 2× NTC 10k or PT1000 sensor; watches the floor temperature limit, does not replace a safety limiter
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring
BALANS POWER Heat Relay (vizualizace)
In development

POWERHeat Relay

Electric heating with metering

A 16 A relay with energy metering and temperature inputs for electric heating.

  • Heating cables, mats, panel heaters; the rated load follows after testing
  • Measures V, A, W and kWh; calibration will be verified on the first unit
  • 230 V AC with neutral · Wi-Fi

Connected by an electrician only. Values are preliminary.

Manual and wiring

Load ratings are preliminary until the temperature-rise tests are finished. 230 V modules are connected by an electrician only.

All modules and parameters

Fitting into the box in 20 seconds

The power module and the controller board go into a standard 68 mm wall box with the carrier. The front panel and glass are put together in the frame separately and snap onto the carrier.

Fitting a BALANS FACE Classic set into a 68 mm wall box (20 s, no sound). Visualisation from the 3D model; the frame and the glass print are a design proposal and the final look may differ.

What BALANS does

Lights and scenes with one touch, blinds via Home Assistant, a thermostat right on the switch and air quality monitoring. Switches talk to each other even without Home Assistant, so a staircase or all-off at the door works without a server too.

An AI-assisted visualisation (44 s, no sound). The display screens follow the firmware; the interiors and hands are illustrative. The POWER Blinds and Heat modules are in preparation.

Integrations

BALANS needs neither a cloud nor a vendor app. You can use it on four levels.

Standalone

Scenes, scheduler, thermostat, timers and night mode right in the switch.

Switch to switch

Staircase wiring and “all off” without Home Assistant.

Smart home

Home Assistant via MQTT discovery, MQTT for Node-RED and others, REST API and webhooks.

Building services

Modbus TCP with PLC blocks (S7-1500 ready, TwinCAT 3 and CODESYS coming up), 24 V inputs and outputs; DALI, 1–10 V and Modbus RTU over RS485 are coming up.

All about integrations All features

Frequently asked questions

Did not find the answer? Write to us.

Is BALANS the same as Smart Button?

Yes. BALANS is the new name of the system we previously presented as Smart Button. The modules got new names too, for example panel 01 is now FACE Classic and module 03B is POWER Triac.

Why is the switch called BALANS?

“Balans” is Czech for balance: the three layers of the switch lie on each other like the ovals in the logo, and the switch balances design and engineering, simple control and smart functions. The name also hides LAN, because everything runs in the local network without a cloud.

When and where can I buy BALANS?

Sales start once the safety, EMC and radio tests are finished and the declaration of conformity is issued. We do not promise an exact date yet. Subscribe to the news and you will be the first to know. If you are building or renovating now, write to us about a pilot installation.

How much does BALANS cost?

We quote on request according to what you need in the room: panel, controller board, power module, glass and frame. Write to benesl@benesl-automation.cz and we will send an offer.

What box does BALANS fit into?

Into a 68 mm installation box (Czech type KPR 68), verified with the Kopos KPR 68-70_KA box, 70 mm deep. Modules with an RJ45 connector (POWER Base, POWER PoE IO) need a depth of at least 60 mm. For other box types, write to us.

Does it work without the internet and without a cloud?

Yes. Touch controls the outputs right in the switch, and the web interface, MQTT, Modbus TCP and Home Assistant all run in your local network. The manufacturer receives no data from the switch.

Which systems does it work with?

With Home Assistant (MQTT discovery, LED notifications, energy, firmware updates, Assist voice satellite), with MQTT systems (Node-RED, openHAB, ioBroker), via REST API and webhooks with anything that speaks HTTP, and with PLCs over Modbus TCP. For Siemens S7-1500 we have a function block in SCL; for Beckhoff TwinCAT 3, CODESYS V3.5 and other PLCs it is coming up. The DALI and 1–10 V modules and Modbus RTU over RS485 are in development. It does not support Matter, Zigbee, Thread or KNX.

Do I need Home Assistant?

No. Scenes, a scheduler with sunrise and sunset, holiday mode, a thermostat with a weekly programme, a staircase timer and night mode run right in the switch, and switches can link to each other. You can add Home Assistant or a PLC any time later.

What can the switch control?

Depending on the POWER module: 230 V lights, dimmed lamps and LEDs, 12/24 V LED strips, DALI luminaires, 1–10 V LED drivers, shutters and blinds, underfloor heating actuators, electric heating with energy metering and 24 V inputs and outputs. And anything else through Home Assistant or a PLC. The DALI, 1–10 V, shutter and heating modules are in development; a dimmer for LED lamps is coming up.

Can I replace the panel or the module later?

Yes. The FACE panel and the POWER module are separate boards. When your needs change (say you want dimming instead of switching), the electrician replaces just the module. The controller board, glass and frame stay.

Can I install the switch myself?

No. Connection to 230 V mains may only be made by a qualified electrician (in Czechia under Government Regulation No. 194/2022). Leave installation, module replacement and repairs to an electrician.

Do I need a neutral wire in the box?

Yes for all modules powered from 230 V (Relay, Triac, DALI, 0–10 V, Blinds, Heat Triac, Heat Relay). The RGBW, Base and PoE IO modules are powered from safety extra-low voltage or from PoE.

Wi-Fi or Ethernet?

Most modules use 2.4 GHz Wi-Fi, so the signal at the switch must be good. Ethernet and PoE come with the POWER Base and POWER PoE IO modules. Touch controls the output right in the switch, so a network outage does not turn the light off.

Does BALANS know I am in the room?

The FACE Sense panel (in development) has a 24 GHz radar that detects even a person sitting still, and a light sensor. It sends presence to Home Assistant or the PLC, where automations decide what to do. The other panels detect an approaching hand and turn on the backlight.

Does BALANS support voice control?

The FACE Display panel will be a Home Assistant Assist voice satellite: it recognises the wake word itself and sends audio only to your Home Assistant, not to a vendor cloud. The feature is coming up.

Is BALANS certified?

Not yet. The modules are prototypes. We are preparing the safety, EMC, radio and cybersecurity (EN 18031) tests and will start selling only after the declaration of conformity is issued. We will publish the declaration with each module in the manuals.

How is the switch set up?

Through the web interface right in the switch, with no app and no account. A wizard takes you through the name and room, the choice of panel and module, touch calibration, Wi-Fi and the connection to Home Assistant. The web has three modes, Standard, Advanced and Expert, so a regular user sees only what they need.

How do I know something is wrong?

The switch reports faults with codes E01 to E26 and a description of what they mean and what to do. You see them in the web interface, in Home Assistant, over MQTT and in the PLC over Modbus, and on a serious fault the backlight flashes red three times. The list of codes is in the CORE board manual.

Does every switch need a temperature sensor?

No. The BME688 sensor is optional. A switch without a sensor takes the temperature from another BALANS switch in the room or from Home Assistant, so the thermostat works anyway.

How is the firmware updated?

In the switch's web interface with a file from the manufacturer. The update is signed, and if the network and the web do not come up afterwards, the switch rolls back to the previous version by itself. Optionally you can enable a nightly automatic update from your own server.

Have all the described features been tested?

We test the basic sets with the Relay, Triac, RGBW and Base modules on prototypes. Newer firmware features and the modules marked “in development” are programmed but still to be verified on the boards. We state this in the status and in the manual of each module.

Can you prepare a custom variant?

Benešl Automation does custom automation. Tell us what you need and we will discuss whether and how BALANS can be adapted.

Be there when BALANS launches

We will e-mail you when the modules go on sale and, once in a while, a short note on how development is going. No spam.

I want a pilot installation Write to us

Privacy policy