Request a quote
Benešl Automation / Articles / Remote PLC access
Technical article · Service and security

Remote PLC access: how to connect to a machine securely

Remote PLC access saves a technician's trip and cuts downtime from hours to minutes. Badly implemented remote access, however, is the shortest way for an unauthorised person to reach a machine's control system. We describe the connection methods used in practice, which one to avoid and the security minimum that makes sense for every machine today.

Ing. Tomáš Benešl · 6 November 2026 · 5 min read

What remote PLC access covers

  • Diagnostics: the state of inputs and outputs, the diagnostic buffer, alarms and an online view of the program.
  • Changes to the PLC program and visualisation, downloading a new version and changing parameters.
  • Program backups and comparing what runs in the PLC with the last handed-over version.
  • Data acquisition and monitoring: trends, piece counts, energy and fault notifications by e-mail or SMS.

The first three require full access to the PLC. The fourth only needs to read data. The distinction matters, because reading data usually needs a much safer setup than changing the program.

What to avoid: a PLC directly on the internet

The simplest and worst solution is to forward the PLC port on the router to the internet. Neither S7 communication nor most industrial protocols were designed for a public network. Search engines for internet-connected devices find such a PLC within hours, and connection attempts arrive automatically. The same applies to the web server of a PLC or panel exposed on a public IP address.

Three methods used in practice

1. A VPN gateway at the machine

An industrial router in the control cabinet creates an encrypted tunnel between the machine network and the technician's computer. The technician then works in TIA Portal or another tool just as if connected by cable. The most common setup uses a relay server: both the router at the machine and the technician's computer connect out to the server, so no port has to be opened in the customer's network. Many manufacturers offer such services, for example Siemens (SINEMA Remote Connect), HMS (Ewon) or Teltonika.

This is the most universal route for program changes and diagnostics. The router should, however, only give access to the machine network, not the whole plant network, and the connection should only be possible on request.

2. Remote desktop on a service computer

A computer with TIA Portal stands at the machine and the technician connects to it with a remote desktop tool. The advantage is that the correct software version and the project stay at the customer's site. The disadvantage is another computer to maintain: updates, antivirus, licences and passwords. Remote desktop should not run permanently and the login should require a second factor.

3. Reading data only

Monitoring, trends and fault notifications do not need access to the program. Data can be read from the PLC via OPC UA or MQTT into a SCADA system or the cloud, ideally through a gateway that cannot write anything into the PLC. Nobody can then reach the PLC from outside, and operations still see what is happening on the machine.

The security minimum for every machine

  • Access on request. The customer switches the connection on, for example with a key switch in the cabinet or in a portal, and switches it off again after the job.
  • A separate machine network. The router only gives access to the machine zone, not to the office network or other lines.
  • Personal accounts and two-factor authentication. No shared password for all technicians, and a record of who connected and when.
  • PLC protection. An access level with a password, PUT/GET access disabled if nothing needs it, and on newer S7-1500 controllers secure PG/HMI communication with certificates.
  • Up-to-date firmware on the router and the PLC, and a program backup before every intervention.

The safety of people at the machine comes first

A remote technician cannot see who is standing at the machine. Before changing the program, downloading a new version or switching the PLC to STOP, they must agree it with the operator on site. The operator confirms that the machine is in a safe state and that nobody is in a hazardous area. Changes to the safety program should not be made remotely, because they must be followed by validation and a function test at the machine itself.

What legislation says

Companies covered by the new cybersecurity legislation transposing the EU NIS2 directive must also manage supplier access to their systems. In practice this means knowing who connects to the machines and how, and having it documented. The new EU Machinery Regulation, which applies from January 2027, additionally requires the machine's control system to be protected against unauthorised interference, including remote interference.

How we set up remote access

For new deliveries we design remote access together with the control cabinet: a separate machine network, a VPN gateway with on-request connection and separate read-only data acquisition. For existing machines we first find out who connects to them today and how, and propose changes. We then use remote diagnostics as part of our service, so most requests are solved without a site visit.

Frequently asked questions

Is it safe to connect a PLC to the internet?

Not directly. The PLC should sit behind a VPN gateway or behind a gateway that only reads data. A forwarded PLC port on a public IP address is found by automated scanners within hours.

Can a program be downloaded to the PLC through remote access?

Yes, over a VPN TIA Portal behaves as if connected by cable. Before downloading, however, you must agree with the operator on site that the machine is in a safe state, and back up the original program.

What if there is no internet at the machine?

Industrial routers can connect via the mobile network. The machine then does not need the customer's network at all, which also simplifies the security approval by IT.

Which VPN gateway should I choose?

One that the customer's IT supports and that all machine suppliers in the plant can work with. One platform for the whole plant is easier to manage than a different router from each supplier.

Related articles and pages

Want to set up remote access to your machines properly?

We review who connects to your machines today and how, and propose a solution that satisfies both IT and service.